搜索资源列表
HexEditor.HEX文件编辑控件
- HEX文件编辑控件，编辑HEX文件，使用RICHEDIT控件实现,HEX file edit control, editing HEX file, use the controls to achieve RICHEDIT
CHexEditDemo
- Recently, I was working on a diagnostic software which requires a Edit Control used for HEX/DEC numbers input. The CEdit that comes with MFC is not so good for this job, as it can not prevent the user from typing an invalid HEX number. Therefore
display_control
- 一个LCD控制器的verilog源代码，可以方便的控制TFT LCD！-An LCD controller Verilog source code, can easily control TFT LCD!
PARK-CAR-RD
- PARK CAR 倒车雷达的制作文件1： 有原理图和控制程序源代码，这里是不用数字显示而只用声音辨别距离的倒车雷达。MOD52是与汇编编译器一起使用的文件，*.HEX文件是编译好的文件，烧录到AT89C2051通电将按其内部的程序工作。图是用Protel 99设计的。更复杂的倒车雷达的制作文件2.3.4将陆续整理后上载-PARK CAR reversing the production of documents Radar 1: There are schematic and source
C51
- 花钱购买的C51学习板里的源码，包括电路图，源码和hex文件，参照图纸接线后，直接烧录可运行。 内容齐全，包括键盘，数码管，温度显示芯片，LCD，ADC数模转换，时钟显示芯片，连接电脑键盘，与电脑通信，蜂鸣器，红外遥控等。。。单片机入门好资料-To spend money to buy the C51 source in the study board, including schematics, source code and hex file, in the light of wirin
hexedit_src
- 一个很好用的十六进制编辑控件，输出文件为OCX-Using a good hex programmer control
control
- 此实验 采用11.0592MHZ晶振 程序下载到芯片后 在电脑上运行串口调试此实验 采用11.0592MHZ晶振 程序下载到芯片后 在电脑上运行串口调试软件 选择好COM口号，设置波特率为57600， 把HEX显示选项打， 在接收框里 ，就可以看到结果了-This experiment uses 11.0592MHZ crystal program downloaded to the chip to run after the computer serial port t
djkz
- 一个可控制步进电机正反转的程序,包括c源文件,hex文件,proteus仿真文件-One can control the stepper motor positive inversion procedures, including the c source file, hex file, proteus simulation file
atmega8_PWM+ADC
- This is a simple program with measure a voltage on ADC pin in Atmega8 AVR uC and control a PWM value . This is a program in CodeVision . I use it for control Lights, motors etc...
XC800_FOC_KEIL
- 英飞凌8位单片机 XC800系列（XC888,XC886等）马达空间矢量控制FOC，KEIL编译调试。适用于无传感器BLDC或永磁同步电机。效率高，噪声低，变频成本相对较低-Infineon XC800 family of 8-bit MCU (XC888, XC886, etc.) the motor space vector control FOC, KEIL compiler debugging. Apply sensorless BLDC or PMSM. High efficiency
jianpanxianshi_huibian
- 计算机测控实验 在六个数码管上显示六位数字 汇编语言编程实现 开发调试程序使用的软件是 KeilC-Computer Control experiments in six six-digit LED display assembly language programming development and debugging software is used by the program KeilC
LCD-Control
- LCD Control using ATMEGA16 ... theres all the project files included in the package (DSN, C, ASM, Hex)
51-stepper-motor-control
- 基于51单片机的步进电机控制。文件包括keil c程序，hex文件，proteus仿真，DXP2004下原理图及pcb版图，最后加上课程（毕业）设计报告。（proteus完美仿真。但因为用的是单个数码管，所以显示的码不对，只需改为四位的数码管即可，共阴共阳的都试一下即可）。另外说明，此程序在min80E开发板上完美实现！！呕心沥血做了三个星期的课设啊~-Based on 51 single-chip stepper motor control. Keil c program files, inc
RF-Based-Remote-control-(AT89C2051)
- (AT89C2051) RF Based Remote control Circuits and Hex Programme File
HEX-TO-DOC
- 1 在上位对下位控制前，把16进制到十进制的转换-1 in the upper lower control hexadecimal to decimal conversion
PWM-control-LED
- 用PWM波控制LED，有hex文件，可以直接烧录。-PWM wave control LED hex file, you can directly burn.
c.hex
- 数码管显示的温控电机设计与仿真，这是c语言程序。是完整的程序-Digital tube display of temperature control motor design and simulation
STM32-test-HEX-files
- Stm32开发板测试文件，由芯嵌嵌入式提供，但不仅适用于芯嵌自己的开发板，详情可查看电路图对照-Stm32 development board test file, provided by the core block embedded, but not suitable for the core block their own development board, please check circuit diagram control
32LED-hex-
- 32路LED控制 包括程序以及原理图，初学者必备材料！-32 LED control procedures including schematics Beginners essential material!
hex-keyboard-example
- hex control, example code for msp430